機械工学の英語論文で頻出の英単語 35 語
機械工学の論文では、stress と strain、strength と stiffness のように、日常では区別しない語が別の量を指します。材料力学・流体・熱・振動・トライボロジーの語は分野をまたいで使われるので、対にして区別すると読みやすくなります。
各語に、品詞、機械工学の論文での意味、一般的な意味との違い(ある場合)、例文を載せています。例文は説明のために作った文で、実在の論文からの引用ではありません。
A
- actuator名詞
- アクチュエータ。電気・油圧・空気圧などのエネルギーを、機械的な動きに変える駆動装置。
- A piezoelectric actuator was used to control the tip position.
B
- boundary condition名詞句
- 境界条件。解析する領域の境界で与える変位・力・温度などの条件。
- Fixed boundary conditions were imposed on the bolt holes.
- boundary layer名詞句
- 境界層。壁の近くで粘性の影響を強く受け、流速が急に変わる薄い層。
- Separation of the boundary layer occurred downstream of the bump.
C
- convection名詞
- 対流(熱伝達)。流体の流れによって熱が運ばれること。強制対流と自然対流がある。
- Forced convection dominated heat transfer at high fan speeds.
- creep名詞
- クリープ。一定の荷重のもとで、時間とともに変形がゆっくり進む現象。高温で顕著になる。
- 一般の意味との違い一般には動詞「忍び寄る、這う」。
- Creep tests were conducted at 650 °C under a constant stress of 150 MPa.
D
- degree of freedom名詞句
- 自由度。機構や物体の運動を決めるのに必要な、独立した座標の数。
- 一般の意味との違い統計の degrees of freedom(自由度)とは別の量。
- The mechanism has a single degree of freedom and is driven by one motor.
- drag名詞
- 抗力。流れの中の物体が、流れの方向に受ける力。
- 一般の意味との違い一般には「引きずること、足手まとい」。
- The riblet surface reduced skin-friction drag by 6%.
- ductile形容詞
- 延性のある。破断する前に大きく塑性変形する。反対は brittle(脆性の)。
- The fracture surface showed dimples characteristic of ductile failure.
E
- excitation名詞
- 加振、励振。構造に振動を起こさせる外力や入力。
- 一般の意味との違い一般には「興奮」。物理学では「励起」。
- The plate was subjected to random excitation using an electrodynamic shaker.
F
- fatigue名詞
- 疲労。繰り返し荷重を受けて、静的な強度より低い応力でき裂が生じ、破壊に至ること。
- 一般の意味との違い一般には「(人の)疲れ」。
- Fatigue cracks initiated at the weld toe after approximately 2 × 10⁶ cycles.
- fillet名詞
- フィレット。部材の角を丸めた部分。応力集中を和らげる。溶接では、すみ肉溶接(fillet weld)を指す。
- 一般の意味との違い一般には料理の「ヒレ肉、切り身」。
- Increasing the fillet radius reduced the stress concentration factor from 2.4 to 1.7.
- finite element名詞句
- 有限要素(法)。領域を小さな要素に分けて、近似的に解く数値解析の方法。FEM、FEA と略す。
- Finite element analysis was performed in Abaqus to predict the deformation.
- friction coefficient名詞句
- 摩擦係数。摩擦力を、接触面に垂直にかかる力で割った値。
- The friction coefficient stabilized at 0.12 after a running-in period.
H
- heat flux名詞句
- 熱流束。単位面積・単位時間あたりに流れる熱量(W/m²)。
- A uniform heat flux of 10 kW/m² was applied to the bottom wall.
K
- kinematics名詞
- 運動学。力を考えずに、位置・速度・加速度の関係だけを扱うこと。ロボットでは関節角と手先の位置の関係。力を扱う dynamics(動力学)と対になる。
- The inverse kinematics of the manipulator was solved analytically.
L
- laminar形容詞
- 層流の。流体が層をなして滑らかに流れる状態の。反対は turbulent(乱流の)。
- The pipe flow remained laminar up to a Reynolds number of about 2,300.
- load名詞
- 荷重。構造や部材に加わる力。
- 一般の意味との違い一般には「積み荷、負担」。電気では「負荷」。
- The beam was subjected to a three-point bending load at mid-span.
- lubrication名詞
- 潤滑。油などで、接触面の摩擦と摩耗を減らすこと。
- The transition from boundary to hydrodynamic lubrication was observed as the sliding speed increased.
M
- mesh名詞
- メッシュ。有限要素法などで、解析する領域を分割した小さな要素の集まり。
- 一般の意味との違い一般には「網、網目」。
- A mesh convergence study confirmed that the peak stress changed by less than 1%.
- mode shape名詞句
- 固有モード、モード形。固有振動数で振動するときの変形の形。
- The second mode shape corresponds to torsion of the blade.
N
- natural frequency名詞句
- 固有振動数。構造が外力なしで自由に振動するときの振動数。
- 一般の意味との違いnatural は「自然な」ではなく「その物に固有の」の意味。
- The first natural frequency of the bracket was 145 Hz, well above the excitation range.
- Nusselt number名詞句
- ヌセルト数。対流による熱伝達を、伝導だけの場合の熱伝達と比べた無次元数。
- The average Nusselt number increased by 40% with the vortex generators.
P
- pressure drop名詞句
- 圧力損失。流体が管や機器を通る間に失う圧力。
- The pressure drop across the heat exchanger increased with flow rate.
R
- Reynolds number名詞句
- レイノルズ数。慣性力と粘性力の比を表す無次元数。層流か乱流かの目安になる。
- Experiments were performed at Reynolds numbers ranging from 5,000 to 50,000.
- rig名詞
- 試験装置。実験のために組んだ装置一式(test rig)。
- 一般の意味との違い一般には「(船の)艤装、石油掘削装置」。
- A test rig was built to measure the bearing temperature under combined loads.
S
- specimen名詞
- 試験片。試験のために、規格の形に加工した材料片。
- 一般の意味との違い一般には「標本、見本」。
- Dog-bone specimens were machined according to ASTM E8.
- stiffness名詞
- 剛性。力を加えたときの変形しにくさ(力 ÷ 変位)。
- 一般の意味との違い一般には「(体の)こわばり」。強度(strength)とは別の量。
- Adding ribs increased the bending stiffness of the panel by 35% with only a 4% increase in mass.
- strain名詞
- ひずみ。変形の度合いを、元の長さに対する伸び縮みの比で表した量(単位なし)。
- 一般の意味との違い一般には「重圧、緊張」。生物学では「系統、株」。
- Strain was measured with gauges bonded to the surface of the specimen.
- stress名詞
- 応力。物体の内部に生じる、単位面積あたりの力(単位は Pa)。
- 一般の意味との違い一般には「ストレス、圧迫」。
- The maximum von Mises stress occurred at the fillet of the shaft.
- surface roughness名詞句
- 表面粗さ。表面の微小な凹凸の大きさ(算術平均粗さ Ra などで表す)。
- Surface roughness decreased from Ra 1.6 μm to 0.4 μm after polishing.
T
- tolerance名詞
- 公差。寸法などに許される誤差の範囲。
- 一般の意味との違い一般には「寛容、耐性」。
- The bore was machined to a tolerance of ±5 μm.
- torque名詞
- トルク。軸を回転させようとする力のモーメント(N·m)。
- The motor delivers a peak torque of 250 N·m.
- turbulence名詞
- 乱流、乱れ。流れが不規則に変動し、大小の渦を含む状態。
- 一般の意味との違い一般には「(社会の)混乱、乱気流」。
- Turbulence was modeled with the k–ω SST model.
W
- wear名詞
- 摩耗。こすれ合う表面から、材料が少しずつ失われること。
- 一般の意味との違い一般には「着ること、衣類」。
- Wear volume was measured with a profilometer after the pin-on-disk test.
Y
- yield動詞
- 降伏する。材料が弾性の範囲を超えて、力を除いても元に戻らない変形(塑性変形)を始める。
- 一般の意味との違い一般には「生み出す、屈する」。化学では名詞で「収率」。
- The specimen yielded at a load of 12 kN, after which plastic deformation localized in the gauge section.
読んでいる論文から、自分の辞書を作る。
Goipon では、機械工学の論文の PDF を開いて、引っかかった単語をタップするだけで、その一文での意味と出典がそろったカードができます。ここにない単語も、自分が読んだ文で覚えられます。
この分野の論文を Goipon で読む
辞書 100 語まで無料。クレジットカードの登録は不要です。